OhSnap Snap Grip Stand review: A $50 MagSafe grip that also sticks to your fridge
The Verge has published a review of the OhSnap Snap Grip Stand, a $50 magnetic phone grip and vertical stand that measures just 3.7mm thin. It attaches to MagSafe-compatible phones and flat metal surfaces alike. Reviewer Sean Hollister tested it on Pixel 9 and Galaxy S25 phones with magnet cases. The Verge
OhSnap first announced the Snap Grip Stand in March 2026 as an evolution of its earlier thin phone grip, adding a folding kickstand that supports a phone in portrait or landscape orientation. The company sells the accessory for $39 on its own site, while The Verge's review cites a $50 price point, likely reflecting retail distribution markup.
The core of the product is a double-sided magnetic ring. One side adheres to phones with built-in magnet rings (or magnet cases); the other sticks to flat metal surfaces such as refrigerators and gym equipment. MagSafe, for readers less familiar, is Apple's magnetic attachment system that uses a ring of magnets to align accessories to the back of a phone. Android manufacturers and case makers have since adopted compatible magnet arrangements.
The grip itself uses interlocking joints that can fit between two fingers or allow a single finger through for a more secure hold. OhSnap's tutorial describes three gripping modes, including a 2-Finger Mode, and instructs users to point the cap marks up and down during use. The disc spins freely to rotate to any angle, though Hollister noted some scraping noise during rotation.
A fold-out ring on a hinged arm props the phone up in vertical orientation. OhSnap describes the stand as a 350° adjustable mechanism that sits nearly flush to the phone and flips out to hold the device at virtually any angle. The company also advertises 360° rotation for the grip portion. In practical terms, the stand covers most viewing angles a user would need, though the 350° figure means there is a small dead zone where the hinge cannot reach.
The build is bare anodized aluminum with no adhesive or soft-touch coating. OhSnap advertises the Snap Grip Stand as "thinner than your camera bumps," a claim that holds up against most flagship camera arrays. The product includes an extra vertical magnet matching Apple's MagSafe pattern, along with grippy clear plastic material to prevent unwanted rotation when mounted. Wireless charging passes through the grip, though the review does not specify charging speeds or whether all Qi-compatible pads work reliably through the 3.7mm layer. Qi is the open wireless charging standard used by most phone manufacturers.
The broader context here is that magnetic phone accessories have proliferated since MagSafe's introduction in 2020. The double-sided ring approach is less common than single-sided MagSafe rings with adhesive backing, and it enables the fridge-and-gym-equipment use case that adhesive-mounted grips cannot serve. The trade-off is that flat metal surface adhesion depends entirely on the surface being ferromagnetic (meaning it attracts magnets) and reasonably flat, which limits where the accessory is useful outside the home.
The 3.7mm thickness figure is worth noting in context. PopSockets and similar collapsible grips typically add 5-10mm of bulk even when collapsed. A sub-4mm profile that still incorporates a rotating disc, a hinged kickstand, and a double-sided magnetic ring is a genuine mechanical packaging achievement, even if the materials are conventional. The scraping noise Hollister observed during rotation suggests the tolerances between the disc and its housing are tight enough to cause friction, which may or may not ease with wear.
The price gap between OhSnap's $39 direct price and The Verge's $50 figure places the Snap Grip Stand in the upper tier of phone grip accessories. Standard PopSockets retail around $10-15, and MagSafe-compatible grips from brands like Anker and ESR typically run $15-30. The Snap Grip Stand commands a premium for its aluminum construction, double-sided magnet, and integrated kickstand. Whether that premium is justified depends heavily on how much the user values the combination of thinness, metal build, and multi-surface mounting in a single accessory.
Looking at the accessory landscape more broadly, the Snap Grip Stand occupies a specific niche: users who want a grip, a stand, and magnetic mounting in one slim profile, and who are willing to pay for aluminum construction rather than plastic. The MagSafe ecosystem has matured enough that the constraint is no longer magnetic attachment reliability, which is now table stakes across major Android and iOS devices with magnet cases. The differentiator has shifted to mechanical design, material quality, and the range of angles and surfaces a single accessory can accommodate. OhSnap's entry checks most of those boxes, with the scraping noise and the narrow dead zone in stand rotation being the notable compromises.
